# TEMPERATURE DISTRIBUTION OF A TEST SPECIMEN WITH HIGH-SPEED HEAT AIRFLOW PASSING THROUGH

## Main Article Content

## Abstract

In this paper, a solution method for the temperature distribution of rectangular test specimen with a high-speed heat airflow passing through is proposed based on the heat transfer theory and numerical calculation, and the feasibility of temperature prediction method is validated. Firstly, the partial differential equations (PDEs) to describe the average temperature in the section of the hot airflow and the specimen are established and the solving method using MATLAB solver is proposed. Then, based on heat transfer conduction equation and the average temperature, the temperature distribution at the different point in each section is calculated. The comparison between numerical computation and experiment shows that two results are in good agreement, which verifies the correctness of the presented prediction method of the temperature distribution of the specimen.

## Article Details

**Thermal Science**, [S.l.], mar. 2017. ISSN 2334-7163. Available at: <http://thermal-science.tech/journal/index.php/thsci/article/view/2297>. Date accessed: 24 feb. 2018. doi: https://doi.org/10.2298/TSCI160302217X.

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors retain copyright of the published article and have the right to use the article in the ways permitted to third parties under the - Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International (CC BY-NC-ND) licence. Full bibliographic information (authors, article title, journal title, volume, issue, pages) about the original publication must be provided and a link must be made to the article's DOI.

The authors and third parties who wish use the article in a way not covered by the the -Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International (CC BY-NC-ND) licence must obtain a written consent of the publisher. This license allows others to download the paper and share it with others as long as they credit the journal, but they cannot change it in any way or use it commercially.

Authors grant to the publisher the right to publish the article, to be cited as its original publisher in case of reuse, and to distribute it in all forms and media.

Accepted 2017-03-14

Published 2017-03-14

## References

[2] Calautit, J. K., et al., CFD and wind tunnel study of the performance of a uni-directional wind catcher with heat transfer devices, Renewable Energy, 83(2015),11, pp. 85-99.

[3] Connor, P. H., et al., Computational fluid dynamics modeling of an entire synchronous generator for improved thermal management, IET in Electric Power Applications, 7(2013), 3, pp.231-236.

[4] Zhang, G.Z., et al., A new model and analytical solution for the heat conduction of tunnel lining ground heat exchangers, Cold Regions Science and Technology, 88(2013), 4, pp. 59-66.

[5] Ferrero, P., D’Ambrosio, D., A Numerical Method For Conjugate Heat Transfer Problems in Hypersonic Flows, 40th Thermophysics Conference, Seattle, Washington, 2008 ,pp.23 – 26.

[6] Wang, C., et al., Thermodynamic Model and Dynamic Temperature Compensation in Positive-Pressure-Based Sonic Nozzle Gas Flow Standard, IEEE Transactions on Instrumentation and Measurement ,62(2013),5, pp.1154-1165.

[7] Ibrahim, M., et al., Effect of Transient Boundary Conditions and Detailed Thermal Modeling of Data Center Rooms, IEEE Transactions on Components, Packaging and Manufacturing Technology, 2(2012), 2, pp.300-310.

[8] Zohir, A. E., et al., Heat Transfer Characteristics in a Double-Pipe Heat Exchanger Equipped with Coiled Circular Wires, Experimental Heat Transfer, 28(2015),6, pp:531-545.

[9] Boonsri, R., Wongwises, S. ,Mathematical Model for Predicting the Heat Transfer Characteristics of a Helical-Coiled, Crimped, Spiral, Finned-Tube Heat Exchanger, Heat Transfer Engineering, 36(2015), 18, pp:1495-1503.

[10] Wae-Hayee, M., et al., Flow and Heat Transfer Characteristics of in-Line Impinging Jets With Cross-Flow At Short Jet-To-Plate Distance, Experimental Heat Transfer, 28(2015), 6, pp.511-530.

[11] Hardik, B.K., et al., Local heat transfer coefficient in helical coils with single phase flow, International Journal of Heat and Mass Transfer, 89(2015), 10, pp. 522-538.

[12] Ronil, R., et al., Effect of Convection Heat Transfer on Performance of Waste Heat Thermoelectric Generator, Heat Transfer Engineering, 36(2015), 17, pp.1458-1471.

[13] Ravnik, J., Škerget, L., A numerical study of nanofluid natural convection in a cubic enclosure with a circular and an ellipsoidal cylinder, International Journal of Heat and Mass Transfer, 89(2015), 20, pp.596-605.

[14] Kitamura, K., et al., Fluid flow and heat transfer of natural convection adjacent to upward-facing, rectangular plates of arbitrary aspect ratios, International Journal of Heat and Mass Transfer, 89(2015), 10, pp. 320-332.

[15] Moon, J.Y., et al., Natural convection experiments on the outer surface of an inclined helical coil, Heat and Mass Transfer, 51(2015), 9, pp.1229-1236.

[16] Aydin, O., Avci, M., Laminar forced convective slip flow in a microduct with a sinusoidally varying heat flux in axial direction, International Journal of Heat and Mass Transfer, 89(2015), 10, pp.606-612.

[17] ASHISH, D., ANIL, K. P., Heat Transfer Characteristics of Grooved Fin Under Forced Convection, Heat Transfer Engineering, 36(2015), 16, pp.1409–1416.

[18] Elnaggar, M.H.A., et al., Experimental and Numerical Studies of Finned L-Shape Heat Pipe for Notebook-PC Cooling, IEEE Transactions on Components, Packaging and Manufacturing Technology, 3(2013), 6, pp.978-988.

[19] ADESANYA,S. O., MAKINDE,O. D., Thermodynamic analysis for a third grade fluid through a vertical channel with internal heat generation, Journal of Hydrodynamics, 27(2015), 2, pp.264-272.

[20] Ji, Z. l., et al., Thermo-plastic finite element analysis for metal honeycomb structure. Thermal Science, 17(2013), 5, pp.1285-1291.

[21] BIirken, P., et al., Fast solvers for unsteady thermal fluid interaction, International journal for numerical methods in fluids, 79(2015), 1, pp.16-29.

[22] Li, Y. H., et al., A novel cascade temperature control system for a high-speed heat-airflow wind tunnel, IEEE-Transactions on mechatronics, 18(2013), 6, pp.978-988.

[23] Cai, C. Z., et al., Compound sliding mode predictive control for a temperature system of high-speed heat-airflow wind tunnel, Proceedings of the institution of mechanical engineers part C-journal of mechanical engineering Science, 228(2014), 11, pp.1869-1879.

[24] Udhayakumar, S., et al., Numerical Experiments on the Study of Mixed Convection Flow in Cylindrical Geometry, Numerical Heat Transfer, Part A, 68(2015), 8, pp. 870-886.

[25] Maytorena, V. M., et al., Experimental and numerical study of turbulent natural convection in an open cubic cavity, Heat and Mass Transfer, 51(2015), 9, pp.1205-1217.

[26] MATLAB R2013a User Guide, Mathworks, February 15, 2013.